SPXCA1-86E EtherCAT Closed-Loop Stepper Driver

Digital Stepper Driver (Pulse/Bus)
SPXCA1-86E is a standalone single-axis EtherCAT closed loop stepper driver with a 24–80 VDC / 20–60 VAC supply and 2.8–5 A output-current range. It supports CSP, PV, PP and HM modes, with three optically isolated programmable inputs.
SPXCA1-86E standalone EtherCAT closed loop stepper driver

Positioning accuracy

High torsional rigidity and constant torsional backlash over the entire gearbox service life ensure consistently high performance

Compactness

High torque density thanks to high performance and short design

Low maintenance

Highest quality standards for a long service life and extended maintenance intervals

Technical data

Single-axis closed-loop control

Closed-loop motion, configured over EtherCAT.

The SPXCA1-86E EtherCAT closed loop stepper driver provides a 2.8–5 A output-current range and a built-in single-axis controller. Use CSP, PV, PP or HM operation and configure current, microstep and standstill-current settings through communication.

EtherCAT motion modes

EtherCAT slave operation supports CiA 301 and CiA 402, with CSP, PV, PP and HM modes for position, velocity and homing tasks on a single axis.

Programmable signal inputs

Three optically isolated programmable inputs provide configurable functions including home, positive and negative limits, emergency-stop input and probe input.

Communication-based setup

A 32-bit RISC-V MCU supports the drive architecture. Configure drive current, microstep settings and standstill current through EtherCAT or serial communication.

Engineering information

Technical data

Match the motor winding, current and feedback requirements to the drive, then verify the EtherCAT master configuration, signal assignments and installation space. Motor frame designation alone does not establish compatibility.

24–80 VDC / 20–60 VACSupply voltage
2.8–5 AOutput current
EtherCATCommunication
1 axisDrive architecture
Specifications

Electrical and signal specifications

SPXCA1-86E electrical and signal specifications
Parameter Specification
Supply voltage 24–80 VDC / 20–60 VAC
Output current 2.8–5 A
Listed motor frames 57 / 60 / 86; verify motor electrical and installation requirements
Listed input functions Home, positive limit, negative limit, emergency-stop input, probe and STO input
Output functions Alarm, in-position, Z-phase, motor-enable and user-defined output
Configuration

Drive and communication functions

SPXCA1-86E drive and communication functions
Function Specification
Drive architecture Standalone single-axis closed-loop stepper driver
Processor 32-bit RISC-V MCU
Network interface EtherCAT slave
Supported profiles CiA 301 and CiA 402
Operating modes CSP / PV / PP / HM
Single-axis controller Built in; synchronous position, velocity, position and homing modes
Programmable inputs 3 optically isolated inputs
Drive configuration Current, microstep and standstill-current settings via EtherCAT or serial communication

The listed input and output functions do not establish physical channel counts or safety performance. Confirm electrical ratings, wiring and the STO implementation before integration. A safety-rated stop function requires appropriate system design and safety documentation.

SPXCA1-86E standalone EtherCAT stepper driver mechanical outline and mounting dimensions
Mechanical outline and mounting dimensions

Confirm dimension units, mounting-hole positions and connector clearance before machining the installation plate.

Standalone drive architecture

A standalone closed-loop EtherCAT drive.

SPXCA1-86E keeps the driver separate from the motor and combines EtherCAT communication with a built-in single-axis controller. Match the 24–80 VDC / 20–60 VAC supply and 2.8–5 A output range to the motor, then configure the selected motion mode and signal functions.

  • EtherCAT slave with CSP, PV, PP and HM modes
  • Current, microstep and standstill-current configuration
  • Three optically isolated programmable signal inputs
SPXCA1-86E standalone EtherCAT closed loop stepper driver
Application selection

Select the mode for your motion task

Evaluate the available operating modes and programmable signals against the machine sequence. Confirm master configuration, motor matching and required stop behavior before commissioning.

01

Position-controlled axes

Assess CSP or PP operation for the required position-command sequence and EtherCAT master configuration.

02

Velocity-mode motion

Review PV operation against the commanded speed sequence and the motor’s operating requirements.

03

Homing sequences

Combine HM operation with the selected home and limit-input assignments for axis referencing.

04

External signal integration

Allocate the three programmable inputs to the required home, limit, emergency-stop or probe functions.

System integration

Confirm the drive and controller configuration

Share the motor and feedback data, EtherCAT master, selected operating modes and signal requirements so our engineering team can review your single-axis drive configuration.

Power supply24–80 VDC / 20–60 VAC
Output-current range2.8–5 A
CommunicationEtherCAT slave
Operating modesCSP / PV / PP / HM
Programmable inputs3 optically isolated inputs

Discuss your EtherCAT stepper-drive requirement.

Send the motor model, supply voltage, EtherCAT master, operating modes and I/O requirements for selection support.

Request consultation →

Contact us

Would you like to learn more about our solutions?
We would be happy to advise you—personally, competently, and tailored to your requirements.

Perfection in a new dimension

SPXCA1-86E EtherCAT Closed-Loop Stepper Driver
SPXCA1-86E is a standalone single-axis EtherCAT closed loop stepper driver with a 24–80 VDC / 20–60 VAC supply and 2.8–5 A output-current range. It supports CSP, PV, PP and HM modes, with three optically isolated programmable inputs.

Further Information

csm walpha vorzugsbaureihen slider 720x490 eaea48abcd

Short delivery times available for selected product configurations.

csm tp plus image 125ef722c4

The TP+ HIGH TORQUE enables maximum torque density and maximum torsional rigidity—ideal for demanding applications with dynamic load changes and high positioning accuracy.

csm tp plus mf flansch korrosion liegend slider 78e8934f42

alpha Advanced Line gearboxes with increased durability and food-grade lubrication available.

csm tp plus ma rmw ritzel zahnstange slider f4c7f6da40

The TP+ for coordinated pinion-rack systems for medium to high requirements. Typical areas of application in wood, plastic, and composite processing, in machining centers, or in automation.

csm cynapse produkseite element slider 08849abb4c

With cynapse® and smart services, you can unleash the full potential of your drive system: sensor data is processed, visualized, and analyzed intelligently. Find out how the combination of gearboxes with cynapse® and our Smart Services can make your digital production faster, safer, and more efficient.

Related products