SPXC1-510 EtherCAT Open-Loop Stepper Driver

Digital Stepper Driver (Pulse/Bus)
SPXC1-510 is a standalone single-axis EtherCAT open loop stepper driver with a 24–50 VDC supply range and 0.1–2.4 A output-current range. It supports CSP, PV, PP and HM modes, with three optically isolated programmable inputs.
SPXC1-510 standalone EtherCAT open loop stepper driver

Positioning accuracy

High torsional rigidity and constant torsional backlash over the entire gearbox service life ensure consistently high performance

Compactness

High torque density thanks to high performance and short design

Low maintenance

Highest quality standards for a long service life and extended maintenance intervals

Technical data

Single-axis EtherCAT control

Networked control for one stepper axis.

The SPXC1-510 EtherCAT open loop stepper driver combines a standalone drive architecture with a built-in single-axis controller. It supports CSP, PV, PP and HM operating modes, with current and microstep settings configurable through communication.

EtherCAT motion modes

EtherCAT slave operation supports CiA 301 and CiA 402, with CSP, PV, PP and HM modes for position, velocity and homing tasks on a single axis.

Programmable signal inputs

Three optically isolated programmable inputs provide configurable functions including home, positive and negative limits, emergency-stop input and probe input.

Communication-based setup

A 32-bit RISC-V MCU supports the drive architecture. Configure drive current, microstep settings and standstill current through EtherCAT or serial communication.

Engineering information

Technical data

Match the motor winding and current requirement to the drive, then verify the EtherCAT master configuration, signal assignments and installation space. Motor frame designation alone does not establish compatibility.

24–50 VDCSupply voltage
0.1–2.4 AOutput current
EtherCATCommunication
1 axisDrive architecture
Specifications

Electrical and signal specifications

SPXC1-510 electrical and signal specifications
Parameter Specification
Supply voltage 24–50 VDC
Output current 0.1–2.4 A
Listed motor frames 20 / 28 / 35 / 42; verify motor electrical and installation requirements
Programmable input functions Home, positive limit, negative limit, emergency-stop input and probe
Output functions Alarm, in-position, motor-enable and user-defined output
Configuration

Drive and communication functions

SPXC1-510 drive and communication functions
Function Specification
Drive architecture Standalone single-axis open-loop stepper driver
Processor 32-bit RISC-V MCU
Network interface EtherCAT slave
Supported profiles CiA 301 and CiA 402
Operating modes CSP / PV / PP / HM
Single-axis controller Built in; synchronous position, velocity, position and homing modes
Programmable inputs 3 optically isolated inputs
Drive configuration Current, microstep and standstill-current settings via EtherCAT or serial communication

Input and output functions are configurable assignments, not separate channel counts. Confirm signal electrical ratings and wiring before connection; the emergency-stop input is not a substitute for a safety-rated stop system.

SPXC1-510 standalone EtherCAT stepper driver mechanical outline and mounting dimensions
Mechanical outline and mounting dimensions

Confirm dimension units, mounting-hole positions and connector clearance before machining the installation plate.

Standalone drive architecture

Bring single-axis control onto EtherCAT.

SPXC1-510 separates the driver from the motor while providing EtherCAT communication and a built-in single-axis controller. Select the operating mode and configure drive parameters for the motor and machine requirements.

  • EtherCAT slave with CSP, PV, PP and HM modes
  • Current, microstep and standstill-current configuration
  • Three optically isolated programmable signal inputs
SPXC1-510 standalone EtherCAT open loop stepper driver
Application selection

Select the mode for your motion task

Evaluate the available operating modes and programmable signals against the machine sequence. Confirm master configuration, motor matching and required stop behavior before commissioning.

01

Position-controlled axes

Assess CSP or PP operation for the required position-command sequence and EtherCAT master configuration.

02

Velocity-mode motion

Review PV operation against the commanded speed sequence and the motor’s operating requirements.

03

Homing sequences

Combine HM operation with the selected home and limit-input assignments for axis referencing.

04

External signal integration

Allocate the three programmable inputs to the required home, limit, emergency-stop or probe functions.

System integration

Confirm the drive and controller configuration

Share the motor data, EtherCAT master, selected operating modes and signal requirements so our engineering team can review your single-axis drive configuration.

Power supply24–50 VDC
Output-current range0.1–2.4 A
CommunicationEtherCAT slave
Operating modesCSP / PV / PP / HM
Programmable inputs3 optically isolated inputs

Discuss your EtherCAT stepper-drive requirement.

Send the motor model, supply voltage, EtherCAT master, operating modes and I/O requirements for selection support.

Request consultation →

Contact us

Would you like to learn more about our solutions?
We would be happy to advise you—personally, competently, and tailored to your requirements.

Perfection in a new dimension

SPXC1-510 EtherCAT Open-Loop Stepper Driver
SPXC1-510 is a standalone single-axis EtherCAT open loop stepper driver with a 24–50 VDC supply range and 0.1–2.4 A output-current range. It supports CSP, PV, PP and HM modes, with three optically isolated programmable inputs.

Further Information

csm walpha vorzugsbaureihen slider 720x490 eaea48abcd

Short delivery times available for selected product configurations.

csm tp plus image 125ef722c4

The TP+ HIGH TORQUE enables maximum torque density and maximum torsional rigidity—ideal for demanding applications with dynamic load changes and high positioning accuracy.

csm tp plus mf flansch korrosion liegend slider 78e8934f42

alpha Advanced Line gearboxes with increased durability and food-grade lubrication available.

csm tp plus ma rmw ritzel zahnstange slider f4c7f6da40

The TP+ for coordinated pinion-rack systems for medium to high requirements. Typical areas of application in wood, plastic, and composite processing, in machining centers, or in automation.

csm cynapse produkseite element slider 08849abb4c

With cynapse® and smart services, you can unleash the full potential of your drive system: sensor data is processed, visualized, and analyzed intelligently. Find out how the combination of gearboxes with cynapse® and our Smart Services can make your digital production faster, safer, and more efficient.

Related products