SPBRC530 RS485 Closed-Loop Stepper Driver

RS485 Closed-loop Stepper Motor & Driver
SPBRC530 is an RS485 closed loop stepper driver with standard Modbus RTU, a 20–50 VDC supply and 0.1–3.0 A peak output current. It supports multi-speed and multi-position control, I/O-triggered internal commands and force-controlled homing.
SPBRC530 RS485 closed loop stepper driver with Modbus RTU

Positioning accuracy

High torsional rigidity and constant torsional backlash over the entire gearbox service life ensure consistently high performance

Compactness

High torque density thanks to high performance and short design

Low maintenance

Highest quality standards for a long service life and extended maintenance intervals

Technical data

RS485 closed-loop control

Serial communication. Sequenced motion.

The SPBRC530 RS485 closed loop stepper driver combines standard Modbus RTU communication with multi-speed and multi-position control. I/O-triggered internal commands and force-controlled homing support equipment sequence planning.

Standard Modbus RTU

RS485 communication supports a maximum baud rate of 115200. Match the controller settings and device address before commissioning.

Multi-segment control

Multi-speed and multi-position control support staged motion sequences. Internal commands can be triggered through I/O to coordinate the required sequence.

Force-controlled homing

Force-controlled homing is supported alongside overvoltage and overcurrent protection. Confirm the homing configuration and machine safeguards before operation.

Engineering information

Technical data

Select a 20–50 VDC supply and verify the motor current, feedback, connector and installation requirements before wiring. Confirm the controller communication settings before commissioning.

20–50 VDCSupply voltage
0.1–3.0 APeak output current
RS485 (Modbus RTU)Communication
115200 baudMaximum baud rate
Specifications

Electrical specifications

SPBRC530 electrical specifications
Parameter Specification Unit
Peak output current 0.1–3.0 A
Supply voltage 20–50 VDC
Typical supply voltage 24 / 36 VDC
Default output current 1 A
Configuration

Drive and communication functions

SPBRC530 drive and communication functions
Function Specification
Drive architecture Standalone closed-loop stepper driver
Communication interface RS485
Communication protocol Standard Modbus RTU
Maximum baud rate 115200 baud
Motion control Multi-speed / multi-position control
Command triggering I/O-triggered internal commands
Homing function Force-controlled homing
Protection functions Overvoltage and overcurrent protection

Confirm the selected supply, motor-current setting and control-signal requirements before wiring. Drive protection functions do not replace the safeguards required by the complete machine.

SPBRC530 RS485 stepper driver mechanical outline and mounting dimensions
Mechanical outline and mounting dimensions

Confirm dimension units, mounting-hole positions and connector clearance before machining the installation plate.

RS485 drive integration

Connect the controller. Configure the sequence.

SPBRC530 operates from a 20–50 VDC supply with a 0.1–3.0 A peak output-current range. Integrate standard Modbus RTU communication with multi-speed or multi-position control, then configure I/O command triggering and the required homing behavior.

  • RS485 with standard Modbus RTU, up to 115200 baud
  • Multi-speed and multi-position control
  • I/O-triggered internal commands and force-controlled homing
SPBRC530 RS485 closed loop stepper driver with Modbus RTU
Application selection

Plan the motion sequence for the task

Review communication, motion commands, I/O triggering and homing together. Confirm motor matching and the machine stopping requirements before equipment commissioning.

01

Multi-speed sequences

Evaluate multi-speed control for equipment with staged speed commands. Confirm each required speed and the transition sequence during selection.

02

Multi-position sequences

Plan multi-position commands around the required travel and stopping points. Verify motor matching and movement limits before commissioning.

03

I/O-triggered operation

Use external I/O to trigger internal commands as part of the equipment sequence. Confirm signal assignments and triggering conditions.

04

Homing and referencing

Review force-controlled homing against the mechanical arrangement and stopping requirements. Confirm the selected configuration before use.

System integration

Confirm the motor and controller configuration

Share the motor model, current and feedback information, selected supply, Modbus RTU controller and required motion sequence so our engineering team can review the configuration.

Power supply20–50 VDC
Peak output-current range0.1–3.0 A
CommunicationRS485 (Modbus RTU)
Maximum baud rate115200 baud
Typical supply voltage24 / 36 VDC
Default output current1 A

Discuss your RS485 stepper-drive requirement.

Send the motor model, supply voltage, controller, motion sequence and I/O requirements for selection support.

Request consultation →

Contact us

Would you like to learn more about our solutions?
We would be happy to advise you—personally, competently, and tailored to your requirements.

Perfection in a new dimension

SPBRC530 RS485 Closed-Loop Stepper Driver
SPBRC530 is an RS485 closed loop stepper driver with standard Modbus RTU, a 20–50 VDC supply and 0.1–3.0 A peak output current. It supports multi-speed and multi-position control, I/O-triggered internal commands and force-controlled homing.

Further Information

csm walpha vorzugsbaureihen slider 720x490 eaea48abcd

Short delivery times available for selected product configurations.

csm tp plus image 125ef722c4

The TP+ HIGH TORQUE enables maximum torque density and maximum torsional rigidity—ideal for demanding applications with dynamic load changes and high positioning accuracy.

csm tp plus mf flansch korrosion liegend slider 78e8934f42

alpha Advanced Line gearboxes with increased durability and food-grade lubrication available.

csm tp plus ma rmw ritzel zahnstange slider f4c7f6da40

The TP+ for coordinated pinion-rack systems for medium to high requirements. Typical areas of application in wood, plastic, and composite processing, in machining centers, or in automation.

csm cynapse produkseite element slider 08849abb4c

With cynapse® and smart services, you can unleash the full potential of your drive system: sensor data is processed, visualized, and analyzed intelligently. Find out how the combination of gearboxes with cynapse® and our Smart Services can make your digital production faster, safer, and more efficient.

Related products