SPXSA57E RS485 Closed-Loop Stepper Driver

RS485 Closed-loop Stepper Motor & Driver
SPXSA57E is an RS485 closed-loop stepper driver with an isolated Modbus RTU interface, 0.0–6.0 A output and AC/DC supply options. It supports speed, position, multi-segment position and homing modes, with 11 optically isolated programmable inputs.
SPXSA57E RS485 closed-loop stepper driver with Modbus RTU

Positioning accuracy

High torsional rigidity and constant torsional backlash over the entire gearbox service life ensure consistently high performance

Compactness

High torque density thanks to high performance and short design

Low maintenance

Highest quality standards for a long service life and extended maintenance intervals

Technical data

RS485 closed-loop control

Serial communication. Flexible motion modes.

The SPXSA57E RS485 closed loop stepper driver combines a 32-bit ARM processor with an isolated RS485 interface supporting standard Modbus RTU. Select speed, position, multi-segment position or homing operation to match the equipment sequence.

Isolated RS485 interface

Standard Modbus RTU communication provides a serial interface for controller integration. Confirm the required communication settings and register definitions before commissioning.

Four motion modes

Speed, position, multi-segment position and homing modes support different motion sequences. Choose the operating mode according to the controller and application requirements.

Programmable control inputs

Eleven optically isolated programmable inputs accept external control signals for driver enable, start/stop and limit functions. Match the signal assignments to the equipment sequence.

Engineering information

Technical data

Select an AC or DC supply within the specified range and verify the motor electrical, feedback and installation requirements. The listed 42 / 57 / 60 frame designations alone do not establish compatibility.

24–70 VDC / 20–50 VACSupply voltage
0.0–6.0 AOutput current
RS485 (Modbus RTU)Communication
11 inputsProgrammable inputs
Specifications

Electrical and signal specifications

SPXSA57E electrical and signal specifications
Parameter Minimum Typical Maximum
Output current (A) 0.0 — 6.0
AC supply voltage (VAC) 20 — 50
DC supply voltage (VDC) 24 36 70
Control-signal input current (mA) 7 10 16
Insulation resistance (MΩ) 50 — —
Configuration

Drive and communication functions

SPXSA57E drive and communication functions
Function Specification
Drive architecture RS485 closed-loop stepper driver
Listed motor frames 42 / 57 / 60; verify motor electrical, feedback and installation requirements
Processor 32-bit ARM
Communication interface Isolated RS485
Communication protocol Standard Modbus RTU
Operating modes Speed / position / multi-segment position / homing
Programmable inputs 11 optically isolated inputs
Listed input functions Driver enable, start/stop and limit functions
Protection functions Overcurrent, overvoltage, undervoltage, phase loss and excessive deviation

Confirm the selected power supply, motor current and control-signal requirements before wiring. Drive protection functions do not replace the safeguards required by the complete machine.

SPXSA57E RS485 stepper driver mechanical outline and mounting dimensions
Mechanical outline and mounting dimensions

Confirm dimension units, mounting-hole positions and connector clearance before machining the installation plate.

RS485 drive integration

Match the communication and motion sequence.

SPXSA57E combines isolated RS485 communication with a 32-bit ARM processor and four motion modes. Select a 24–70 VDC or 20–50 VAC supply, match the motor-current requirements, and allocate the 11 programmable inputs before commissioning.

  • Isolated RS485 with standard Modbus RTU
  • Speed, position, multi-segment position and homing modes
  • 11 optically isolated programmable inputs
SPXSA57E RS485 closed loop stepper driver with isolated Modbus RTU communication
Application selection

Choose the motion mode for the task

Review the motion sequence, Modbus RTU controller configuration and external signals together. Confirm motor matching and the required stopping behavior before equipment commissioning.

01

Speed-control tasks

Evaluate speed mode for motion sequences requiring a commanded speed. Confirm the controller settings and motor requirements.

02

Positioning tasks

Use position-mode selection to plan commanded movements. Verify the motion limits and feedback configuration for the chosen motor.

03

Multi-segment sequences

Assess multi-segment position mode against the required sequence. Confirm the available segment configuration and triggering method during selection.

04

Homing sequences

Review homing mode and the external signal assignments for axis referencing. Confirm the required sensors and stopping conditions.

System integration

Confirm the motor and controller configuration

Share the motor model, winding and feedback information, selected supply, Modbus RTU controller, motion mode and signal assignments so our engineering team can review the configuration.

Power supply24–70 VDC / 20–50 VAC
Output-current range0.0–6.0 A
CommunicationRS485 (Modbus RTU)
Listed motor frames42 / 57 / 60
Programmable inputs11 optically isolated inputs
Typical DC supply voltage36 VDC

Discuss your RS485 stepper-drive requirement.

Send the motor model, supply voltage, controller, required motion mode and signal requirements for selection support.

Request consultation →

Contact us

Would you like to learn more about our solutions?
We would be happy to advise you—personally, competently, and tailored to your requirements.

Perfection in a new dimension

SPXSA57E RS485 Closed-Loop Stepper Driver
SPXSA57E is an RS485 closed-loop stepper driver with an isolated Modbus RTU interface, 0.0–6.0 A output and AC/DC supply options. It supports speed, position, multi-segment position and homing modes, with 11 optically isolated programmable inputs.

Further Information

csm walpha vorzugsbaureihen slider 720x490 eaea48abcd

Short delivery times available for selected product configurations.

csm tp plus image 125ef722c4

The TP+ HIGH TORQUE enables maximum torque density and maximum torsional rigidity—ideal for demanding applications with dynamic load changes and high positioning accuracy.

csm tp plus mf flansch korrosion liegend slider 78e8934f42

alpha Advanced Line gearboxes with increased durability and food-grade lubrication available.

csm tp plus ma rmw ritzel zahnstange slider f4c7f6da40

The TP+ for coordinated pinion-rack systems for medium to high requirements. Typical areas of application in wood, plastic, and composite processing, in machining centers, or in automation.

csm cynapse produkseite element slider 08849abb4c

With cynapse® and smart services, you can unleash the full potential of your drive system: sensor data is processed, visualized, and analyzed intelligently. Find out how the combination of gearboxes with cynapse® and our Smart Services can make your digital production faster, safer, and more efficient.

Related products